Industrial Safety Practice Test

These questions are part of the practice quiz. Start practicing

• How does ventilation influence exposure to airborne hazards and what types of ventilation exist?
• Risk factors that lead to musculoskeletal disorders (MSDs) are:
• It is a safe practice to make a three-prong plug fit into a two-prong wall socket by removing the grounding post.
• Which item is specifically recommended to be removed before electrical work?
• A fall protection anchor point must be designed to withstand the loads of a fall at least equal to 5000 pounds per worker.
• A three point-climb means a ladder must be attached at three points.
• In safety terminology, which statement correctly defines risk?
• Which type of vehicles are not covered by 29 CFR 1910.178, Powered Industrial Trucks?
• It is not necessary to chock the wheels of a trailer every time you enter or exit on a fork truck.
• Which of the following is an example of a safeguarding device that stops the machine when the guard is opened?
• In a properly wired 120 V circuit, the hot wire is generally:
• Assuming that lockout is impossible, when is it permissible to bypass OSHA's tagout procedures?
• Which statement best describes a Safe Work Procedure (SWP)?
• Which statement on hazardous waste management is accurate?
• The most important safety consideration for workers entering a confined space is the:
• Workers exposed to brake dust must guard against lung disease by:
• Why is proper ventilation balancing important for safe airborne exposure levels?
• When a circuit breaker trips, you should immediately reset it.
• Guardrails must be installed on any work surface elevated at least:
• Which of the following is not a common symptom of musculoskeletal disorders (MSD)?
• Federal regulation requires that a hearing conservation program must be provided to employees whose exposure is equal to the average noise level of Busy city street traffic.
• What kind of machine guard requires no physical barrier between the operator and the danger zone?
• List the standard sequence of steps in a LOTO procedure.
• The hot conductor in a standard 120 V circuit is typically which color?
• What are the goals and typical elements of an emergency drill and how is effectiveness evaluated?
• Slips, trips and falls cause the majority of general industry accidents and 15% of all accidental deaths.
• Class B fires involve:
• Before climbing a ladder, which practice is essential?
• Which tool is not typically considered a vibrating hand tool that could contribute to an MSD?
• Ohms Law states that:
• Which of the following describes proper PPE usage?
• If a 20-ft ladder is placed against a building with the top 4 feet extending above the top of the wall, the base of the ladder should be from the wall.
• Before you disconnect a pneumatic tool, turn off the air supply and:
• Which of the following is not a basic means of safeguarding equipment?
• Which of the following is not a vibrating tool that could contribute to an MSD?
• Which of the following is a typical responsibility of a safety officer on a worksite?
• What is a near miss and why should it be reported?
• In a LOTO program, what is the purpose of verifying zero energy?
• Which organization is responsible for regulating chemicals in the environment?
• Which of the following tools is not a vibrating tool that could contribute to an MSD?
• Fuses and circuit breakers are designed to protect people from shocks.
• Which statement best describes risk factors for musculoskeletal disorders (MSDs)?
• Which statement about hearing protection is true?
• Which item is not a vibrating hand tool that can contribute to MSD risk?
• Which elements are essential in a respiratory protection program?
• Machine guards that cannot be moved when the machine is in operation are called:
• What is the role of an attendant during a permit-required confined space entry?
• Which action most directly supports prevention of recurrence after an incident?
• Which practice most effectively enhances forklift safety and on-site traffic management?
• Heatstroke symptoms include all of the following EXCEPT:
• Refuel gasoline engines only after the engine has cooled.
• Which information must be included on a GHS-compliant label?
• Which of the following should a hot work permit typically identify?
• Water puts out a fire by:
• A ground fault can be defined as:
• Before performing any electrical work, which personal items should be removed to reduce risk?
• A hot work permit is required for operations that produce heat, sparks, or open flames; what does it typically authorize?
• Which factor is important when selecting gloves for handling corrosive liquids?
• Which practice helps prevent cross-contamination in chemical storage?
• Which feature is essential to prevent falls from scaffolds?
• Which statement best reflects safe tool usage from the material?
• When you must lift a heavy object, which rule should you follow?
• When evacuating for a fire, you should:
• The statement 'A three point-climb requires the ladder to be secured at three points' is:
• Intrinsically safe electrical equipment is designed to:
• Why is high-quality training and supervision important for preventing slips, trips, and falls?
• Which statement about slips, trips, and falls is most accurate?
• Which guard is described as requiring no physical barrier between the operator and the danger zone?
• What is ergonomics?
• Which class of fire extinguisher is used for flammable liquids?
• What is arc flash and which standard provides guidance for electrical safety?
• In Ohm's Law, resistance is measured in the unit called:
• A good tool can be made defective by trying to make it do more than it was designed to do.
• Which statement correctly describes fire extinguisher inspection frequency and classes?
• What is a key reason for prequalification of contractors before work on-site?
• Which scenario best illustrates the purpose of lockout/tagout procedures?
• Is it safe to use pocket knife to open cartons or boxes in the workplace?
• Which items are typically required before entry into a permit-required confined space?
• Which statement best describes the role of Safe Operating Procedures (SOPs) in a workplace?
• To use a wrench safely, you should:
• What considerations guide PPE selection and what are its limitations?
• Which document defines the locking and tagging procedures and required inspections?
• The majority of injuries from material handling affect the:
• What is the correct step before disconnecting a pneumatic tool?
• What defines a permit-required confined space (PRCS) and what entry prerequisites are typical?
• After you have locked out the power to a machine, you should:
• Most conveyor accidents occur during maintenance.
• Which statement about modifying a plug to fit a two-prong outlet is correct?
• Under what conditions should you wear gloves when working with revolving electric tools?
• How does worker participation influence safety performance?
• According to the hierarchy of controls, which control category should be applied first?
• Outline the typical steps for incident reporting and investigation within 24 hours of occurrence.
• What is the purpose of secondary containment in chemical storage?
• Which step is included in a Job Hazard Analysis (JHA) process?
• The anchor point of a fall protection system must be capable of supporting at least 5000 pounds per worker.
• Which element in an Emergency Action Plan is NOT typically included?
• The most common method of preventing the accumulation of static electricity is:
• To prevent Class C fires, you should:
• Which item is not a risk factor for repetition-related MSD?
• Why is labeling and dating containers important?
• Hot, dry skin, headache, rapidly rising temperature, and fainting are all symptoms of:
• Most of the injuries resulting from the accidental start-up of conveyors can be prevented if:
• Overloading a tool beyond its design capacity can cause it to fail.
• What strategies support workplace violence prevention and response?
• If you touch someone who is in contact with an electrical source, you will:
• Which of the following is typically considered a hazardous electrical location?
• For a 20-foot ladder with the top extending 4 feet above the wall, the base distance from the wall should be:
• The purpose of the EPA is to:
• Which of the following is not a recognized risk factor for repetitive MSD?
• Which action best describes a safe startup procedure after maintenance?
• Which of the following is NOT a component of a personal fall arrest system?
• What can you do to avoid injury in the workplace?
• Which statement is true?
• By far the hazard related to abrasive grinding wheels that could cause the most severe injury is:
• Fall protection systems may be connected to water or sewer lines or an electrical conduit.
• Which of the following best reflects the safety practice regarding jewelry when working with electricity?
• If a machine guard is more than 3 feet from the point of operation, the maximum opening is?
• Most accidents involving conveyors happen when the machine is being repaired or undergoing routine maintenance.
• How should a chemical spill be contained and cleaned up safely?
• Which regulation covers Powered Industrial Trucks?
• Which of the following is a factor to consider when selecting respiratory protective equipment (RPE)?
• How do hot work permits differ from cold work permits?
• Which of the following is NOT typically considered a data collection step in an incident investigation?
• Which element best prevents falls on scaffolds?
• To allow for proper step off and access, a ladder should extend at least above the top support by how many feet?
• An effective electrical safety program should include:
• How should the SDS be used in daily operations during chemical handling?
• What is the very first thing to do when an electrical accident occurs?
• During evacuation, which route is recommended to minimize exposure to smoke?
• When is it safe to stand on a suspended load?
• The four elements in the fire pyramid are fuel, heat, oxygen, and a:
• What metric is commonly used to evaluate the effectiveness of an emergency drill?
• What is the purpose of safety signs and color codes, and what are common color meanings?
• Which practice helps maintain safe air quality in chemical storage areas?
• Exposure to loud noise can cause negative health effects other than hearing loss.
• Which body part is most vulnerable to welding-related hazards such as bright light?
• Class A fires involve:
• Non-ionizing radiation includes which of the following?
• After use, a pump-tank water extinguisher must be:
• Which of the following is not typically associated with musculoskeletal disorders?
• What is the recommended ladder angle relative to the ground for safe use?
• How do lockout/tagout devices and hasps differ?
• Intrinsically safe electrical equipment is designed to:
• A confined space atmospheric testing protocol should include which elements?
• When energizing electrical equipment, the electrical enclosure door should be:
• Which safety management cycle maps to planning, doing, checking, and acting to improve safety processes?
• What term best describes alpha, beta, and gamma radiation?
• Which statement best describes the role of fuses and circuit breakers in electrical systems?
• During welding, which part of the body is especially vulnerable to the light, radiation, heat, and sparks?
• A hoist is only as strong as its weakest part.
• Which basic precaution is recommended around energized electrical equipment?
• You should operate a forklift only if:
• What is the purpose of a lockout/tagout annual inspection and who should perform it?
• Which type of control helps reduce noise exposure by rotating workers?
• What information do HazCom pictograms communicate, and how do they support safety decisions?
• If a machine guard is more than 3 feet from the point of operation, what is the maximum opening?
• Water extinguishes a fire primarily by which mechanism?
• Which factor would NOT typically increase the likelihood of MSD from repetition?
• What are leading indicators of safety performance?
• Which measure best reduces risk when servicing equipment by controlling energy flow?
• Which statement about incident investigation phases is true?
• Only ___________ and trained workers are permitted to work on or near exposed electrical components.
• What should be included in an energy control program?
• Which elements form the safety management system improvement loop?
• Which practices help prevent musculoskeletal disorders in the workplace?
• Lockout/tagout must be used whenever employees are performing servicing or maintenance of machines or equipment where they could be injured by unexpected start-up or release of stored energy.
• Is it safe to stand on the top rung of a ladder when the ladder is too short for the work to occur?
• What tasks typically require a Permit-to-Work system?
• Which of the following is an example of a machine guarding safeguard?
• Extension cords should never be used as a permanent power source.
• Which practice is least aligned with hazardous waste management?
• What is a Safe Work Procedure (SWP) and how is it used?
• Which action helps prevent injuries due to unexpected machine energization during maintenance?
• Awkward postures that you may experience while performing your job include all of the following except:
• Which location is considered hazardous for electrical work due to industrial operations?
• If an electrical accident victim's pulse or breathing has stopped, brain damage can occur within the following timeframe.
• Alpha, beta, and gamma radiation are all kinds of radiation.
• Which item is NOT typically included in an Emergency Action Plan?
• One way to protect your hearing is to:
• Why is effective contractor safety management essential and what practices improve it?
• Fuses and circuit breakers act as ______ in electric circuits.
• The purpose of the grounding wire in an electric tool is to protect against:
• Which statement about handling gas cylinders is accurate?
• Which body part is most affected by welding hazards such as bright light?
• Brake dust exposure requires guarding against lung disease caused by which substance?
• Which of the following is a good rule for lifting?
• It is never safe to stand under a suspended load.
• A personal fall arrest system should include which of the following components?
• What is the purpose of Lockout/Tagout (LOTO) and when is it used?
• The three basic means of safeguarding equipment are:
• Which of the following is an engineering control used to reduce airborne hazards?
• Which of the following is not a risk factor that determines if repetition contributed to an MSD?
• Radar, microwaves, and infrared light are all kinds of ___ radiation.
• Which problem-solving tools are commonly used in incident investigations and what do they achieve?
• HazCom versus SDS: How do they differ?